Thermwood collaborates on large-scale composite AM cure tool programme

Thermwood has announced it has played a key development partner role in a Navy ManTech-funded programme issued to Boeing Research and Technology. 

The ManTech programme was managed by Advanced Technology International (ATI) for the Office of Naval Research (ORN) with funding provided from the Naval Air Systems Command (NAVAIR) Aircraft Equipment Reliability & Maintainability Improvement Programme (AERMIP). Fleet Readiness Centre East (FRCE) was a key technical contributor for the low cost composite cure tooling technology development.

LFAM tool after autoclave cure
LFAM tool after autoclave cure

Thermwood’s Large Scale Additive Manufacturing (LSAM) machine was selected as the Large Format Additive Manufacturing (LFAM) machine to conduct the technology development. Several unique equipment features of the LSAM machine drove the selection. The high temperature autoclave cure tooling operating environment of 355°F and 85psi provides a challenge for polymer based tool material. Additional composite cure tooling requirements for vacuum integrity and dimensional stability were validated during the development. 

“Composite manufacturing is a strategic technology for future platforms and development of more cost-effective tooling solutions would significantly benefit the implementation,” notes Neil Graf from the Office of Naval Research.

FRCE provided a high contour mould line surface to Boeing for generating the composite cure tool. The mould line shape was very aggressive and would stretch the large format additive manufacturing technology processes capability. The spherically shaped portion of the mould line offered the largest challenge, as the unsupported 3D printed angle limitation of approximately 45° provides an interesting obstacle to overcome for the spherical mould line section of the tool. Boeing rotated the 3D print plane 35° to avoid encroachment of the build angle limitation.

The new innovative build plane approach eliminated the requirement for temporary support material for the aggressive mould line shape. The new build angle would test the LSAM machine limits in an area never explored previously. The Techmer PM PESU CF 1810 high temperature print material was used for the composite cure tool. High temperature materials present additional challenges during print over low temperature materials such as ABS CF. Two interim support features were added to compensate for the centre of gravity shift of the print. The LSAM machine performed flawlessly during the composite cure tool print. The tool was printed in 7 hours and 26 minutes using 610lbs of material.

The composite cure tool was machined in 53 hours using the LSAM gantry router machine. The tool datum features, and removal of interim members, were machined prior to removal from the bead-board. The Thermwood LSAM machine offers the ability to machine and 3D print on a single platform. The composite cure tool mould line part surface achieved at surface profile tolerance of 0.020” (±0.010”).

The Boeing Research and Technology (BR&T) laboratory performed functional testing on the LFAM composite cure tool to ensure vacuum integrity and dimensional stability requirements were reached. The LFAM tool performed as expected and achieved all requirements. Several composite parts were fabricated from the tools. The tool durability was assessed during the multiple autoclave cure cycles and fabricated (3) composite parts. The tool maintained dimensional stability and vacuum integrity throughout the functional testing and composite part manufacturing.

The composite cure tool was printed and NC machined on Thermwood’s Large Scale Additive Manufacturing (LSAM) 1020 machine. The LFAM technology cost savings was estimated at 50% compared to traditional tool fabrication methods, and reduced tool fabrication lead-time by 65%. The cost savings and tool fabrication cycle time reduction could provide enormous benefit to any organisations performing low volume or custom composite part fabrication and repair.

Non-destructive Inspection (NDI) was performed on the composite parts fabricated on LSAM tools. The NDI results did not indicate any porosity. Due to the complex shape of the composite demonstration part several NDI process were employed. X-ray and C-Scan results did not reveal any delaminations or defects.

Composite part fabricated from LFAM tool
Composite part fabricated from LFAM tool

The programme benefited from a cooperative effort among several contributors to achieve success. The partnership between industrial technology leaders, Boeing and Thermwood coupled with the Office of Naval Research’s drive to transition technology, led to the successful programme. 

“Collaborations such as this help expand the scope of capabilities of emerging large scale additive technology by addressing real world challenges that would be difficult for any single entity to define and address by itself,” says Thermwood CEO, Ken Susnjara. “We look forward to new challenges moving forward.” 

Additional development is key to expand LFAM composite cure tooling implementation. 

“The programme provided significant results in validating additive manufacturing as a viable method of producing lower cost, capable tooling with substantial time savings over traditional methods,” concludes Boeing associate technical fellow, Michael Matlack.

www.thermwood.com

Related Articles

Speaker line-up announced for TCT Show 2016

TCT Show, a specialist event dedicated to 3D manufacturing tech, has announced the speaker line-up for the 21st TCT Show Conference and details of the comprehensive exhibitor list.
7 years ago News

Thermwood announces 3D additive manufacturing programme

Thermwood Corporation has announced it is now offering a line of additive manufacturing systems for the production of large reinforced thermoplastic composite parts. The company’s new machine line, called Large Scale Additive Manufacturing (LSAM), uses a two-step, near-net-shape production process.
7 years ago Products

Thermwood LSAM

Thermwood's LSAM (Large Scale Additive Manufacturing) is used for the production of large reinforced thermoplastic composite parts. The company’s new machine line uses a two-step, near-net-shape production process.
7 years ago Videos
Most recent Articles

Exel secures deal with Chinese bus builder

Finnish composite manufacturer Exel Composites has secured a new project with Chinese automotive manufacturer Foton Bus and Coach Company to supply pultruded glass fibre composite profiles.
20 hours ago News

Zünd establishes branch in Australia

Zünd Systemtechnik has announced the establishment of its own branch in Australia. Zund Australia will be based in Melbourne serving existing and new customers from all areas of application in which Zünd is active.
2 days ago News

Login / Sign up