Exel Composites carbon fibre parts complete 9 years' service at CERN

CIMDec17News - exel
CIMDec17News - exel

Carbon fibre components designed and manufactured by Exel Composites have successfully completed 9 years of service in a high precision application at CERN's Large Hadron Collider (LHC) particle accelerator in Geneva.

Carbon fibre components designed and manufactured by Exel Composites have successfully completed 9 years' of service in a high precision application at CERN's Large Hadron Collider (LHC) particle accelerator in Geneva.

As a key part of the particle tracker support structures for the LHC's Compact Muon Solenoid (CMS) detector, Exel's pultruded profiles had to satisfy strict dimensional tolerances and sustain the highest level of performance in this extremely challenging environment, where any downtime or failure would impact major scientific experiments.

The LHC is the world’s largest and most powerful particle accelerator. It consists of a 27km ring of superconducting magnets with a number of accelerating structures to boost the energy of the particles along the way. Inside the accelerator, two high-energy proton beams travel at close to the speed of light, in opposite directions, before they are made to collide at four locations around its ring. The CMS detector sits at one of the four collision points and records the paths taken by particles using a silicon tracker consisting of around 75 million individual electronic sensor channels arranged in 12 concentric layers. The tracker needs to record particle paths with very high precision yet be lightweight so as to disturb the particles as little as possible.

Exel Composites’ components are part of the 688 high-precision structures supporting the silicon tracker modules. These are made up of two 1.2m long Exel carbon fibre epoxy composite U-profiles of 0.7mm wall thickness and L-shaped cross-bars to form a frame structure on which the particle detecting modules sit. In addition to delivering the lightweight and radiation transparency required for this application, it was critical that the Exel profiles met extremely tight tolerances in terms of dimensions and straightness and maintained all mechanical properties at the low temperatures encountered in the CMS. In order to provide the high levels of stiffness and thermal stability required, Exel designed the profiles using high modulus unidirectional (UD) carbon fibre. A thin glass fibre surface tissue was also employed to facilitate processing. All of the components and fixtures were then assembled and bonded on jigs at the Helsinki Institute of Physics to create structures with a dimensional tolerance of ± 0.05mm.

Exel's proven capabilities in the production of high performance thin-walled pultruded profiles and the company's extensive experience in designing with high modulus carbon fibres were key success factors in this project. Exel had also collaborated successfully with CERN before, supplying around 200km of electrically insulating glass fibre profiles to frame the superconductive busbars of the LHC.

Exel delivered the tracker support profiles to CERN from 2001 to 2005, with the final operational use starting in 2008. The CMS detector has been performing excellently, culminating in 2012 with the discovery of a new elementary particle, the Higgs boson.

"We are very satisfied with the high level of technology and development support offered by Exel Composites," commented Antti Onnela, CMS Tracker Project Engineer at CERN. "We had quite challenging requirements for these composite structures and earlier laminated versions did not meet them. Exel developed the needed thin-walled U-profiles that turned out to be technically superior, but also more economical thanks to the production process that minimised the wastage of expensive carbon fibres. After 9 years in service in the CMS the Exel parts continue performing as flawlessly as in the beginning."

Kari Loukola, Exel Composites’ senior vice-president, sales & marketing added: "We are very proud that Exel profiles have delivered the precision and performance essential for the operation of this extremely complex instrument. This project is a further example of how our pultrusion technology enables the production of profiles of superior quality which will provide customers with reliable performance in the most demanding of environments for many years to come."

www.exelcomposites.com

Company

Exel Composites

Related Articles

Origine Bicycles turns to TeXtreme to reduce weight and improve durability

French bike brand Origine Bicycles looked to make more durable still lightweight frames and to achieve their goals they turned to TeXtreme. Utilising their knowledge and novel spread tow carbon fibre materials resulted in an optimised frame lay-up that already have shown a heavy reduction in frame breakages.
7 years ago News
Most recent Articles

Exel secures deal with Chinese bus builder

Finnish composite manufacturer Exel Composites has secured a new project with Chinese automotive manufacturer Foton Bus and Coach Company to supply pultruded glass fibre composite profiles.
6 days ago News

Zünd establishes branch in Australia

Zünd Systemtechnik has announced the establishment of its own branch in Australia. Zund Australia will be based in Melbourne serving existing and new customers from all areas of application in which Zünd is active.
1 day ago News

Login / Sign up